Model F120HB High Accury Single-axis Fiber Optic Gyroscope With
0.01°/hr Bias Drift
1. Product introduction
1.1 Working Principle and Function
This product is an inertial angular rate sensor based on the
principle of Sagnac effect, which is used to measure the angular
rate movement of the carrier around the sensitive axis of this
sensor. This unit takes the fiber optic coil as the angular rate
sensitive unit and the closed-loop detection circuit as the basis.
Two beams from a laser are injected into the same fibre but in
opposite directions. Due to the Sagnac effect, the beam travelling
against the rotation experiences a slightly shorter path delay than
the other beam. The resulting differential phase shift is measured
through interferometry, thus translating one component of the
angular velocity into a shift of the interference pattern which is
measured photometrically.
Beam splitting optics launches light from a laser diode into two
waves propagating in the clockwise and anticlockwise directions
through a coil consisting of many turns of optical fibre. The
strength of the Sagnac effect is dependent on the effective area of
the closed optical path: this is not simply the geometric area of
the loop but is enhanced by the number of turns in the coil.
This product is an inertial sensor composed of optical system,
corresponding power supply and data processing circuit. It can
provide three-axis angle increment information.
1.2 Configuration
The product is mainly composed of the following components:
a) Optical part: light source, coupler, Y modulator, fiber coil,
detector;
b) Circuit part: processor board, light source board and
preamplifier;
c) Structural part: body, cover, etc.1.3 shape and installation
size
1.3 Shape and installation size
Outline size (120 ± 0.1)mm × (120 ± 0.1) mm × (38 ± 0.5)mm,
Installation dimensions (94 ± 0.1 mm) × (94 ± 0.1mm)
1.4 Weight
850g ± 20g
1.5 Performance parameters
| Index name | Index requirements | Remarks |
Range of measured angular rate (°/s) | ±300 | |
Scale Factor Non-linearity at fixed temperature (ppm) | ≤5 | |
Asymmetry of scaling Factor at Romm Temperature (ppm) | ≤5 | |
Scale Factor Repeatability at fixed temperature (ppm) | ≤5 | |
Scale Factor Reperatability at full temperature range from －40℃ till 60℃ (ppm) | ≤30 | |
Bias Drift at fixed tumperature (10s,1σ,°/h) | ≤0.01 | |
Bias Drift Repeatability at fixed temperature (1σ,°/h) | ≤0.01 | |
Bias Drift Repeatability at full temperature range from －40℃ till 60℃ (1σ,°/h) | ≤0.01 | Fixed-point constant temperature test |
Bias Drift at full temperature range from －40℃ till 60℃ (100s,1σ,°/h) | ≤0.1 | Off line compensation |
Random Walk (°/√h) | ≤0.003 | |
Warm up time (min) | 0 | |
Random vibration (°/h) | ≤0.1 | The difference between the mean of zero deviation before and after vibration |
Shock (°/h) | ≤0.1 | Zero deviation before and after impact |
| Resolving power | ≤0.5 | |
Zero deviation change bdfore and after vibration (°/h) | ≤0.01 | |
Zero bias sensitivity (°/h/GS) | ＜0.5 | |
| Storage temperature | －50℃~70℃ | |
| Operating temperature | －40℃~60℃ | |
1.6 Mechanical and electrical interfaces
1.6.1 Mechanical interface
The mounting surface of the product constitutes the fixed surface
for external installation, and the mounting screw is M6.
1.6.2 Power requirements
Dc power supply: ± (5 V±0.25V)
Ripple: 20mV
The output power: ≥6W
1.6.3 Electrical interface
| Zja12-01t socket pin number | Physical meaning | Note |
| 1 | ＋5V | |
| 2 | GND | |
| 3 | －5V | |
| 9 | | The reserved interface |
| 10 | | The reserved interface |
| 11 | T＋ | |
| 12 | T－ | |
